What is the difference between Tubes and Pipes? Pipes are majorly round, and Tubes are rugged and come in plenty of shapes. Tube fittings are the essential part of the tubes that need to add or curve the tube to specific directions. There are plenty of tube fittings that are used to connect and fix two or more tubes.

Tube fittings are applied in plenty of industries. Tube fittings are an essential part that functions in significant parts. Tube fittings are implied to connect tubes. The fittings must be specific, and component selection is a must. Tube fittings have plenty of applications, prominently in hydraulic and pneumatic systems. Here are some applications of tube fittings.

 

Hydraulic Application:

It is where the liquid is transferred, like water or chemicals. Tight sealing is required in fittings to prevent leakage and better material to avoid corrosion.

 

Pneumatic Application:

It is where gasses are transferred in tubes. The tube fittings must be tightly installed to prevent any leakage. The fitting must be resistant to the corrosive nature of the gas.

 

Types of Tube Fitting.

 

Various types of Tube Fittings are crucial in numerous industries. The attachment of tubes with two leading types, Compression fitting, and Threaded Fitting.

 

Compression Fittings

Compression fittings connect tubes by using a gasket, ring, or ferrule. Compression is used to tighten the grip and have a fixed hold between two types securing the lines. The standard reduction doesn't require additional fittings, but they are very susceptible to high pressure. Contraction also defies heated substances, and proper tube fittings are required.

 

Bite-type fitting:

Bite-type fittings are compression-based fittings with a sharpened ferrule that presses the tube like a bite. When compressed a seal is created to secure the tube components to flow flawlessly. No unique tool is used to fix the joint, and this fitting is not sturdy and better for high-pressure connection.

 

Mechanical Grip Fittings:

Mechanical grip fittings have two ferrule assemblies, one in front and another behind. The back ferrule holds the tub while putting pressure against the front ferrule. The spring-loaded front ferrule creates a seal between the tubing and the fitting body. The mechanical grip can be attained multiple times and is not permanent.

 

Flare Fitting:

Flare fitting has a body with a coned end. A unique flaring tool is used to fit the tube in the tapered end. The small coned end tightens the seal and handles pressure with a broad range than standard compression fitting.

 

Threaded Fitting.

 

Threaded fittings have screw heads on both sides for connecting both tubes. It is a simple yet effective connection with no sealing. The treads intertwine with each other to provide a robust grip. Sealing can be added with an external coating over the threaded joint. Threaded tube fittings are highly operated in multiple industries.

 

Male and Female Connectors:

Male connectors have a threaded exterior, and female connectors have a threaded interior. The male connector is attached to one tube and the female to the other. A male connector is fitted into the female connectors to join the tubes.

 

Unions:

Unions are couplings with both ends threaded to connect the two ends of the tube. They can be disconnected without needing to cut them. A reducer union minimizes the flow of the substance present in the lines.

 

Couplings:

A coupling is used to connect two tubes by welding them together. It created a strong bond with no leakages of fluids or gasses. Couplings don't perform with pressured content and are permanent.

 

Elbow Fittings:

Elbow fittings are utilized to change the course of tubes to different angles. Both ends are threaded and stable materials are used to handle the extreme pressure on the bends. The elbow fittings are made in multiple angles, like 45 degrees and 90 degrees. Male Elbow fittings have outer threads that go in the joining pipe. Female elbow fittings have the connecting pipe go over it to join the line.

 

Tee Fittings:

Tee fittings allow three tube connections. It has a male thread and two female threads to ensure the leading pipe has a secure fit. To connect the prominent tube with the other two lines with a sturdy grip. The material used to construct tee fittings is better compared to others as it handles higher pressure from the pipe contents.

 

Union Cross:

Union cross is similar to a tee but with one additional joint. It offers four connections of equal connections. It is used to mix two fluids, and the construction is solid. The center is exceptionally solid and made to sustain high pressure and more corrosion.

 

Tub Caps:

Tube caps don't connect two lines, but restrict one. It is used to seal off the end of a line to stop its contents from flowing. Caps are made of higher-quality stainless steel tube fitting to withstand the pressure to stop the flow of tube fluids or gasses.

 

Tube Plug:

A tube plug is similar to a cap, but the only difference is the way it is attached. A plug is a male thread inserted into the tube with a threaded interior. The grip is better, and is also welded firmly to secure its position.

 

Instrumxx Industries is the leading tube fittings manufacturer in India. They excel in tube fittings and valve supply throughout the countries and foreign land. One benefit of their fittings is the variation in products and the materials used to construct them. Unlike the others, Instrumxx Industries has better personalization as they manufacture the products. So clients can avail of a personalized size with standard dimensions to attain the best tube fittings and more.

 

Here is the list of products Instrumxx Industries manufactures, exports and supplies.